Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use Bedienungsanleitung Seite 133
- Seite / 148
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
132 CHAPTER 12 PROGRAMMING CONTACT CLOSURES
two channels. If you would like to use more than two channels, you will need a 4-channel
card or you will need to daisy-chain rack cards together.
Note
It is recommended to select a channel order using the sensor configuration software,
rather than using step 2 of the rack card.
Fail Safe Mode
If the rack card is in fail-safe mode (constant call on all channels), you can check connectiv-
ity by connecting an RS-485 to RS-232 converter (Click 304) to the T-bus expansion slot on
the trac cabinet assembly. e sensor’s RS-232 port is completely independent and may
become unreliable at communication lengths greater than 200 . (61 m).
Rack Card Dip Switch
If you are seeing calls on the rack card LEDs, but do NOT see them registering in your
controller, you may need to disable the rack card’s pull-up circuitry. To do so, use the dip
switch on the rack card circuit board. If pull-up is enabled, the rack card will pull its back-
plane contact pins high when the contact is open. However, if pull-up is disabled, the rack
itself will need to pull the contact pins high when the contact is open. In either case, when a
contact closure occurs, it is the responsibility of the rack card to pull the associated contact
pin low (see Figure 12.3).
Rack card DIP switch
Figure 12.3 – Dip Switch on the Click 172/174 Cards
Once the contact closure card is congured, the controller’s detector inputs must be set up
and then assigned to the correct phases of the intersection.
- SmartSensor Advance 1
- SmartSensor 2
- Contents 4
- Introduction 6
- SmartSensor Advance Package 7
- Selecting a Detection Method 7
- Selecting a Mounting Location 8
- Installing the SmartSensor 14
- Selecting the Mounting Height 16
- Mounting the Sensor 17
- Distance 18
- Oset (perpendicular) 18
- Aligning the Sensor 20
- Figure 1.9 – Viewpoint 1 21
- Using the Viewfinder 22
- To target 23
- Figure 1.12 – Viewpoint 1 23
- Grounding the Sensor 26
- Connecting Power and 28
- Surge Protection 2 28
- Mounting the Backplate 29
- Connecting AC Power 29
- Push this button to 32
- (see Figure 2.8) 35
- Contact Closure Connections 37
- Using SmartSensor Manager 38
- Advance 3 40
- Figure 3.3 – Shortcut Options 42
- Communication 4 44
- Serial Connection 45
- Internet Connection 46
- Virtual Connection 47
- Virtual Sensor File 48
- Selecting a Tracker Log File 49
- Multi-drop Network 50
- Address Book 51
- Check Hardware 53
- Communication Error Log 54
- Sensor Settings 5 58
- Figure 5.2 – General Tab 59
- Communication Tab 60
- Sensor Configuration 6 62
- 1. Installation Details 63
- Positioning the Sensor 64
- 3. Manual Radar Adjustment 66
- Editing Sensitivity 67
- Changing the PGA 70
- Channels-Alerts-Zones 7 72
- Channels 73
- Channel 1 74
- Priority Channel 75
- Pulse Channel 78
- Normal Channel 80
- Latched Channel 82
- Enabling an Alert 85
- Logic (OR/AND) 85
- Inverted Zones 85
- Range (ft) 86
- Speed (mph) and ETA (s) 87
- Right Sidebar 93
- (All) Channels 94
- Individual Channel 95
- Channel LED 97
- Zone LED 98
- Alert LED 98
- Roadway Display 99
- Qualified Count 102
- Dynamic Density 103
- Tri-view 104
- Tracker Highlighting 105
- Left Sidebar 107
- Figure 8.24 – Log File 109
- Figure 8.25 – Pulse Log File 109
- In this chapter 110
- Primary Push Manager 111
- Specify output frequency 112
- Secondary Push Manager 113
- Templates 10 116
- Creating a Channel Template 117
- Importing a Channel Template 117
- 118 CHAPTER 10 TEMPLATES 119
- Tools 11 120
- Backup/Restore Tool 121
- Restoring the Configuration 122
- Restoring to Factory Defaults 123
- Beam Alignment Tool 124
- Serial Terminal 125
- Rack Card Tools 126
- Using the Rack Card Tool 127
- Firmware Version 128
- Signal Cards Switch 128
- Channel Outputs Switch 128
- Fail Safe Mode 133
- Rack Card Dip Switch 133
- Click 104 Configuration 135
- Appendix 138
- Creating Custom Cables 139
- Appendix B – Cable Lengths 140
- APPENDIX 143 144
- APPENDIX 145 146
- 146 APPENDIX 147
Verwandte Produkte und Handbücher für Sensoren Wavetronix SmartSensor Advance Extended Range (SS-200E) - Use
(78 Seiten)
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern